How To Remove Coaxial Cable From Modem

Download Article

Download Commodity

Coaxial cable tin can exist used to transmit a variety of signals, including cablevision television set, cyberspace and low quality audio. If y'all're working on a projection that falls in whatever of these categories, you can brand your own cables and save money by learning how to terminate coaxial cable yourself.

Steps Download Article

1. 1

   Get together your materials. In order to end a coaxial cable, you will need the post-obit tools and materials:

   • Coax compression connector - At that place are several types of connectors bachelor. Pinch connectors provide the all-time connexion and terminate to your cable. The 2d-best type of connectors are "crimp" connectors. Avoid button-on or twist connectors.
   • Pinch/crimping tool - Make sure it is compatible with the compression/crimping connector.
   • Coax cable stripper tool
   • Cable cutters
   • Connector installation tool - This tool is used for pushing the connector firmly onto the stripped cable.

2. ii

   Brand a straight cut at the finish of the cablevision. Utilise your cutting tool to make a straight cut at the terminate of the cablevision. After cutting, utilize your fingers to form the finish of a cable back into a circumvolve.

   Advertisement

3. 3

   Adjust your stripper to work with your cable. Most coaxial strippers tin exist adjusted to strip dual-shielded or quad-shielded coaxial cables. Use the included Allen wrench to adjust the stripper. If y'all don't adapt the stripper properly, you lot may strip the ground wire, damaging the cable.

   • The most common cable is RG-half-dozen, either quad- or dual-shielded. Brand sure that the stripper is configured for RG-6 coaxial cable, and not another cable size such as Ethernet cable.
   • If your stripper is set up to dual-shielding, but you endeavour to strip a quad-shielded cablevision, not all of the shielding will be removed.

4. four

   Strip the end of the coax cable. Place the finish of the coax cable into the stripper so that the end of the cable is affluent with the far end of the stripper. Clamp the stripper down on the cable and spin it around the cable two to three times.

   • Yous can tell when the stripper is finished when you don't feel resistance anymore when spinning.
   • Don't pull the stripper off when finished. Unlatch it and open it to remove the cablevision.

5. v

   Pull off the outer shield. After stripping the cable, you should run into two segment cuts. Pull the outermost segment off of the cable. This should reveal the heart conductor wire.

6. 6

   Pull off the 2nd segment. This will reveal the foil that insulates the cablevision. Find the edge of the foil and peel it off the cable. This should leave a single layer of foil around the white insulation.

7. 7

   Fold dorsum the braid. When y'all pull off the cablevision jacket, you volition encounter a lot of loose ground wires. Fold these back against the cable so that the connector volition be touching all of the wires when installed. None of the wires should be blocking the white insulation.

8. viii

   Cutting the usher wire (if necessary). Most cablevision stripper tools will exit the correct length of conductor wire exposed, only it doesn't hurt to double bank check before proceeding. The exposed connector cable should be 3.9 mm (.156 inches) in length.

9. 9

   Put the connector onto the stripped end of the cable. Use a pusher tool to firmly push the connector onto the cablevision until the white insulation is affluent with the connector.

   • Make sure you avert bending the blank conductor wire when installing the connector.
   • Yous may need to twist the cable while pushing with the tool to get it firmly continued.

10. 10

    Compress or crimp the connector. The procedure for compressing or crimping the connector varies depending on the type of connector you are using. Some require you to printing downwards on the cablevision-end of the connector slice, while others require you lot to push the forepart and end of the connector piece into each other.

    • Squeeze the compression or crimping tool firmly. Nearly tools won't permit you lot to over-compress, but some tin cause harm to the cablevision and connector if compressed too much.

11. 11

    Inspect the connectedness for imperfections. Later on you accept finished compressing the connector, inspect information technology for any stray wires or loose connections. These can atomic number 82 to a bad signal or nonfunctional cable.

Ad

Add New Question

• Question

  Can you lot tell me how to remove these compression connectors, and can it be washed without a special crimping tool?

  

  Become regular pliers and place the jaws on the "humps" on the crimped connector and squeeze slightly. There are usually four "humps," so y'all would practise this once on each pair. If this does not work, simply cut off the stop. Then you would strip the end again to attach a new connector. These connectors cannot be reused, but tin be replaced past "twist-on" connectors which do not demand a tool.

Inquire a Question

200 characters left

Include your electronic mail address to become a message when this question is answered.

Submit

Advertisement

Video

• Once you lot have adjusted the stripping tool for the brand of cablevision you are using, it won't strip other brands of cablevision properly without readjustment. Use 1 brand of cablevision for your whole projection.

• There are several unlike types of coaxial cable and connectors. A few of the more commonly used are ADC DSX-CM-thousand, WECO Blazon 734A, Belden YR23922, Belden 1505A and GEPCO VPM2000. The most commonly used coaxial connectors are BNC-734 and TNC-734.

• If the coaxial cable has a foil shield underneath the braided shield, y'all want information technology cut to the aforementioned dimensions as the braided shield.

Thank you for submitting a tip for review!

Advert

Almost This Commodity

Thanks to all authors for creating a page that has been read 257,127 times.

Is this article upward to date?

Source: https://www.wikihow.com/Terminate-Coaxial-Cable

Share this post